Private:

Lang: Lua Plain text Python Shurtle Bash Batch Brainf**k C C++ CSS Common Lisp Common lisp Diff HTML IRC Logs Java Javascript Julia Julia console NASM PHP Perl PowerShell Python Console Python Traceback VB.NET XML YAML

Text: P2601HN-F3 login: DSL[00]: DSL_DRV_HandleEventCallback: Got Dying Gasp interrupt # # # # # # # # # # # ROM VER: 1.ù ROM VER: 1.1.3 CFG 01 ZyU-F01-200-01CA004-V2.00|01/27|2011(UTR) Boot from NOR flash AR9 BOARD CLOCK CPU 333M RAM 166M DRAM: 64 MB relocate_code start relocate_code finish. Flash: 16 MB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: switch chip id=0000ffff switch chip id=0000ffff amazon_s Switch ## Starting application at 0x86A80000 ... Z-LOADER 2.0(Jan 27 2011) check z-boot 1, checksum: 522e, 522e load zboot from b0020000 to 86a90000 go 0x86a90000 ## Starting application at 0x86A90000 ... Z-Boot 2.0.0(Oct 6 2011) Protected 1 sectors Hit any key to stop autoboot: 0 ROM-D check=0 MRD_CERT_1 check=0 MRD_CERT_2 check=0 bootargs=root=/dev/mtdblock0 console=ttyS1,115200 phym=64M mem=62M panic=1 vpe1_load_addr=0x83e00000M vpe1_mem=2M vpe1_wired_tlb_entries=1 ## Booting image at 80800000 ... Image Name: MIPS Linux-2.6.20 Created: 2011-10-06 3:51:38 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1249227 Bytes = 1.2 MB Load Address: 80002000 Entry Point: 8039e000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... Infineon xDSL CPE AR9 mips_hpt_frequency = 166666666, counter_resolution = 2 Linux version 2.6.20.19 (release@holyBuild) (gcc version 4.3.3 (GCC) ) #54 Thu Oct 6 11:51:25 CST 2011 phym = 04000000, mem = 03e00000, max_pfn = 00003e00 Reserving memory for CP1 @0xa3e00000, size 0x00200000 CPU revision is: 0001954c Determined physical RAM map: User-defined physical RAM map: memory: 03e00000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Built 1 zonelists. Total pages: 15748 Kernel command line: root=/dev/mtdblock0 console=ttyS1,115200 phym=64M mem=62M panic=1 vpe1_load_addr=0x83e00000M vpe1_mem=2M vpe1_wired_tlb_entries=1 1 MIPSR2 register sets available Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). Cache parity protection disabled Lantiq ICU driver, version 3.0.1, (c) 2001-2010 Lantiq Deutschland GmbH PID hash table entries: 256 (order: 8, 1024 bytes) Using 166.667 MHz high precision timer. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 58720k/63488k available (2963k kernel code, 4712k reserved, 728k data, 180k init, 0k highmem) Security Framework v1.0.0 initialized Mount-cache hash table entries: 512 NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 2048 bind 1024) TCP reno registered gptu: totally 6 16-bit timers/counters gptu: misc_register on minor 63 gptu: succeeded to request irq 118 gptu: succeeded to request irq 119 gptu: succeeded to request irq 120 gptu: succeeded to request irq 121 gptu: succeeded to request irq 122 gptu: succeeded to request irq 123 IFX DMA driver, version ifxmips_dma_core.c:v1.0.9 ,(c)2009 Infineon Technologies AG Lantiq CGU driver, version 1.0.9, (c) 2001-2010 Lantiq Deutschland GmbH Wired TLB entries for Linux read_c0_wired() = 0 squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher squashfs: LZMA suppport for slax.org by jro JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. yaffs Oct 6 2011 11:46:30 Installing. Infineon Technologies DEU driver version 1.0.1 IFX DEU DES initialized (multiblock). IFX DEU AES initialized (multiblock). IFX DEU ARC4 initialized (multiblock). IFX DEU SHA1 initialized. IFX DEU MD5 initialized. IFX DEU SHA1_HMAC initialized. IFX DEU MD5_HMAC initialized. io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered (default) io scheduler cfq registered ifx_pmu_init: Major 251 Lantiq PMU driver, version 1.1.4, (c) 2001-2010 Lantiq Deutschland GmbH Lantiq GPIO driver, version 1.2.12, (c) 2001-2010 Lantiq Deutschland GmbH Infineon Technologies RCU driver version 1.0.6 Lantiq LED Controller driver, version 1.0.4, (c) 2001-2010 Lantiq Deutschland GmbH Lantiq MEI driver version: 5.01.03 ttyS0 at MMIO 0xbe100400 (irq = 98) is a IFX_ASC ttyS1 at MMIO 0xbe100c00 (irq = 105) is a IFX_ASC Lantiq ASC (UART) driver, version 1.0.5, (c) 2001-2010 Lantiq Deutschland GmbH RAMDISK driver initialized: 1 RAM disks of 12288K size 1024 blocksize loop: loaded (max 8 devices) PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered PPP MPPE Compression module registered NET: Registered protocol family 24 IFX SWITCH API, Version 1.0.1 SWAPI: Registered character device [switch_api] with major no [81] Loading A5 (MII0/1 + ATM) driver ...... Succeeded! PPE datapath driver info: Version ID: 32.3.7.0.0.0.4 Family : AR9 DR Type : Normal Data Path | Indirect-Fast Path Interface : MII0 | MII1 | ATM Mode : N/A Release : 0.0.4 PPE firmware info: Version ID: 5.2.4.6.1.32 Family : AR9 FW Type : Acceleration Interface : MII0/1 + ATM Mode : Bridging + IPv4 Routing Release : 1.32 PPA API --- init successfully ifx_nor0: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 ifx_nor0: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. ifx_mtd_init flash0: Using static image partition Creating 5 MTD partitions on "ifx_nor0": 0x00040000-0x00ee0000 : "rootfs,kernel" 0x00ee0000-0x00f00000 : "mrd_romd" 0x00f00000-0x00fc0000 : "systemconfig" 0x00fc0000-0x00fe0000 : "mrd_cert1" 0x00fe0000-0x01000000 : "mrd_cert2" Lantiq MTD NOR driver, version 1.0.4, (c) 2001-2010 Lantiq Deutschland GmbH Lantiq SSC driver, version 2.2.2, (c) 2001-2010 Lantiq Deutschland GmbH usbcore: registered new interface driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver usbcore: registered new interface driver pegasus Registered led device: phoneVM_led Registered led device: phone_led Registered led device: wps_led Registered led device: power_led Registered led device: internet_red_led Registered led device: internet_led Registered led device: dsl_led Registered led device: wireless_led Lantiq LED driver, version 1.0.15, (c) 2001-2010 Lantiq Deutschland GmbH Mirror/redirect action on u32 classifier Performance counters on input device check on Actions configured Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (496 buckets, 3968 max) nf_ct_ftp: registering helper for pf: 2 port: 21 nf_ct_ftp: registering helper for pf: 10 port: 21 ip_conntrack_rtsp v0.6.21 loading ZLD: zy_sm_init() register hooks successful. IPv4 over IPv4 tunneling driver GRE over IPv4 tunneling driver ip_nat_rtsp v0.6.21 loading ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 Bridge firewalling registered Ebtables v2.0 registered ebt_ulog: not logging via ulog since somebody else already registered for PF_BRIDGE NET: Registered protocol family 8 atmpvc_init() failed with -17 lec.c: Oct 6 2011 11:48:38 initialized mpc.c: Oct 6 2011 11:48:35 initialized 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com> VFS: Mounted root (squashfs filesystem) readonly. Time: MIPS clocksource has been installed. Freeing unused kernel memory: 180k freed init started: BusyBox v1.10.4 (2011-10-06 12:08:07 CST) starting pid 151, tty '': '/etc/init.d/rcS' Algorithmics/MIPS FPU Emulator v1.5 Run init.d/rcS! /etc/init.d/rcS: line 7: cannot create /etc/mtab: Read-only file system tar: removing leading '/' from member names Trying to mount NOR flash as JFFS2 for configuration files Running all S1 scripts in /etc/init.d/etc/init.d/rcS: line 91: TIMEZONE_CONFIG=/mnt/Config: not found Starting syslog-ng... load hidden_flash_access.ko hidden_flash: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 hidden_flash: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. init_hidden_flash_access_module() SUCCESS ===> Dump Default Romfile and FW Info dump & decompress ROM-D file to /var/default-pdm/config.romd.xml successfully! ================================================== = ZyCLiP Version Information = ================================================== ZyCLiP : 2.0.0.0 ZLOader : 2.0 Z-Boot : 2.0.0 Run S1_10ethernet to load Ethernet module First get MAC address=EC43F6283720 Create MAC = EC:43:F6:28:37:20 Create MAC = EC:43:f6:28:37:21 Create MAC = EC:43:f6:28:37:22 Create MAC = EC:43:f6:28:37:23 Create MAC = EC:43:f6:28:37:24 Create MAC = EC:43:f6:28:37:25 Create MAC = EC:43:f6:28:37:26 ifx_ppa_init - init succeeded Insert BTN IO module GPIO phy addr:1e100b10, len:58, vir addr: be100b10 LED phy addr:1e100bb0, len:14, vir addr: be100bb0 init_gpio_reg /proc/btn_io is created init_btn_io_module() SUCCESS, Major Numer is 220 Enable BTN_timer. Run S1_12xdsl to load xdsl module init_internet_led_control_module() SUCCESS, Major Numer is 225 Wan pin select is 1 (0:Ethernet wan, 1:DSL wan) Lantiq CPE API Driver version: DSL CPE API V4.6.3.5 Predefined debug level: 3 >>>>debug: get wan mode ADSL Bring up ADSL Modem is not ready! ADSL Annex B nReturn=0 nReturn=0 Loads switch module S17 Insert switch control module Run S1_20voip to load ZyIMS module #### Tune MIPS-34k VPE Priority for VoIP #### IFXOS, Version 1.5.11 <6>(c) Copyright 2007, Infineon Technologies AG <6>### IFXOS - IFXOS - IFXOS - IFXOS ### Lantiq TAPI device driver, version 3.13.0.2, (c) 2001-2010 Lantiq Deutschland GmbH <6>IFX KPI egress tasklet registered to group 1 Lantiq KPI2UDP driver, version 2.2.0.0, (c) 2008-2010 Lantiq Deutschland GmbH modprobe: module softdog_vpe not found modprobe: failed to load module softdog_vpe Lantiq MIPS34KEc MPS driver, version 2.2.2.5, (c) 2006-2010 Lantiq Deutschland GmbH Lantiq VMMC device driver, version 1.9.0.3, (c) 2006-2010 Lantiq Deutschland GmbH BRIDGE_DEV=br0 device eth0 is not a slave of br0 device eth0.10 entered promiscuous mode eth0.10: dev_set_promiscuity(master, 1) device eth0 entered promiscuous mode br0: port 1(eth0.10) entering learning state Enable switch vlan function !!! Enabling IP forwarding Bringing up interface lo params = lo 127.0.0.1 Starting USB driver... Insert ifxusb_host.ko module dwc_otg1: version 2.2-RC3 100713 dwc_otg1 dwc_otg1: DWC OTG Controller dwc_otg1 dwc_otg1: new USB bus registered, assigned bus number 1 dwc_otg1 dwc_otg1: irq 54, io mem 0x00000000 Reg USB power!! DWC_otg: Init: Power Port (0) usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected starting ftpd... usb 1-1: new high speed USB device using dwc_otg1 and address 2 usb 1-1: configuration #1 chosen from 1 choice done /etc/init.d/S1_99local: line 27: /etc/init.d/multiboot.sh: not found k_wdt: module license 'unspecified' taints kernel. starting hardware watchdog... Enable switch vlan function !!! Starting ZLD CCC(Common Configuration Center)... RESET CCC LOG LEVEL: 6 RESET CCC LOG LEVEL: 6 RESET CCC LOG LEVEL: 6 touch: invalid option -- t finish download certificate rm: cannot remove '/etc/allcert/all.pem': No such file or directory BusyBox v1.10.4 (2011-10-06 12:08:07 CST) multi-call binary Usage: touch [-c] FILE [FILE...] Update the last-modified date on the given FILE[s] Options: -c Do not create any files Starting mini_httpd... socket: Address family not supported by protocol can't get rdm Layer3Forwarding object Layer3Forwarding.DefaultConnectionService value is wrong. Start ROM Convert... starting pid 703, tty '': '/sbin/getty 115200 ttyS1' (none) login: mkdir: cannot create directory '2': Read-only file system BE DHCPCLIENT init eth0.10: dev_set_promiscuity(master, -1) device eth0 left promiscuous mode device eth0.10 left promiscuous mode br0: port 1(eth0.10) entering disabled state ======================================= resetAllPPPDUnitNumberStatus(): pppdUnitNumberInUsed[0]=0 pppdUnitNumberInUsed[1]=0 pppdUnitNumberInUsed[2]=0 pppdUnitNumberInUsed[3]=0 pppdUnitNumberInUsed[4]=0 pppdUnitNumberInUsed[5]=0 pppdUnitNumberInUsed[6]=0 pppdUnitNumberInUsed[7]=0 ======================================= sh: cannot create cp6c/dev/null: nonexistent directory ifconfig: nas1: error fetching interface information: Device not found cp: cannot stat '/etc/sysconfig/network-scripts/wan-multi/ifcfg-eth0': No such file or directory ifconfig: bad address '1500' device nas1 is not a slave of br0 cat: can't open '/var/tmp/hosts': No such file or directory mkdir: cannot create directory '2': Read-only file system RTNETLINK answers: No such file or directory RTNETLINK answers: No such file or directory RTNETLINK answers: No such file or directory RTNETLINK answers: No such file or directory RTNETLINK answers: No such file or directory RTNETLINK answers: No such file or directory RTNETLINK answers: No such file or directory RTNETLINK answers: No such file or directory RTNETLINK answers: No such file or directory RTNETLINK answers: No such file or directory device eth0 is not a slave of br0 eth0.3901: dev_set_promiscuity(master, 1) device eth0 entered promiscuous mode device eth0.3901 entered promiscuous mode br0: port 1(eth0.3901) entering learning state cat: can't open '/tmp/schedule/*.sche': No such file or directory killall: crond: no process killed killall: updatedd: no process killed Symbol usb_register_driver is being used by a non-GPL module, which will not be allowed in the future Please see the file Documentation/feature-removal-schedule.txt in the kernel source tree for more details. Symbol usb_deregister is being used by a non-GPL module, which will not be allowed in the future Please see the file Documentation/feature-removal-schedule.txt in the kernel source tree for more details. rtusb init ---> === pAd = c02a0000, size = 625056 === <-- RTMPAllocAdapterBlock, Status=0 usbcore: registered new interface driver rt2870 $LOCAL_ADMIN_MAC=Ee:43:F6:28:37:24 <-- RTMPAllocTxRxRingMemory, Status=0 -->RTUSBVenderReset <--RTUSBVenderReset Key1Str is Invalid key length(0) or Type(0) Key1Str is Invalid key length(0) or Type(0) Key1Str is Invalid key length(0) or Type(0) Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) 1. Phy Mode = 9 2. Phy Mode = 9 NVM is Efuse and its size =2d[2d0-2fc] ERROR!!! E2PROM: WRONG VERSION 0x4, should be 1 3. Phy Mode = 9 MCS Set = ff 00 00 00 01 SYNC - BBP R4 to 20MHz.l Channel 1 : QUA_Dirty = 48 Channel 2 : QUA_Dirty = 56 Channel 3 : QUA_Dirty = 64 Channel 4 : QUA_Dirty = 598 Channel 5 : QUA_Dirty = 112 Channel 6 : QUA_Dirty = 132 Channel 7 : QUA_Dirty = 136 Channel 8 : QUA_Dirty = 248 Channel 9 : QUA_Dirty = 96 Channel 10 : QUA_Dirty = 397 Channel 11 : QUA_Dirty = 104 Channel 1 : ch_List = 8 Channel 2 : ch_List = 9 Channel 3 : ch_List = 10 Channel 4 : ch_List = 100 Channel 5 : ch_List = 18 Channel 6 : ch_List = 22 Channel 7 : ch_List = 22 Channel 8 : ch_List = 41 Channel 9 : ch_List = 16 Channel 10 : ch_List = 66 Channel 11 : ch_List = 17 Main bssid = ee:43:f6:28:37:24 <==== rt28xx_init, Status=0 0x1300 = 00064380 device ra0 entered promiscuous mode device ra1 entered promiscuous mode device ra2 entered promiscuous mode device ra3 entered promiscuous mode Terminate the task(RtmpMlmeTask) with pid(1027)! Terminate the task(RtmpCmdQTask) with pid(1028)! Terminate the task(RtmpTimerTask) with pid(1026)! Terminate the task(RtmpWscTask) with pid(1029)! br0: port 2(ra0) entering disabled state br0: port 3(ra1) entering learning state br0: port 4(ra2) entering learning state br0: port 5(ra3) entering learning state <-- RTMPAllocTxRxRingMemory, Status=0 1. Phy Mode = 9 2. Phy Mode = 9 ERROR!!! E2PROM: WRONG VERSION 0x4, should be 1 3. Phy Mode = 9 MCS Set = ff 00 00 00 01 Main bssid = ee:43:f6:28:37:24 <==== rt28xx_init, Status=0 0x1300 = 00064380 br0: port 2(ra0) entering learning state br0: topology change detected, propagating br0: port 1(eth0.3901) entering forwarding state rm: cannot remove '/etc/igmpv3.conf': No such file or directory iptables v1.3.8: interface name `ruletmp:/sbin/crond' must be shorter than IFNAMSIZ (15) Try `iptables -h' or 'iptables --help' for more information. sh: -p: not found Jan 1 00:00:51 ccc_be: beSysMtnReloadConfig(): Loading beVoipConfigLoad... *********************************************** zyims is not running , just start up zyims Restarting killall: voiceApp: no process killed killall: mm.exe: no process killed killall: icf.exe: no process killed MaxLineCount = 8 GetWanInterfaceDnsName: get_voip_iface_address fail GetWanInterfaceDnsName: get_voip_iface_address fail br0: topology change detected, propagating br0: port 3(ra1) entering forwarding state br0: topology change detected, propagating br0: port 4(ra2) entering forwarding state br0: topology change detected, propagating br0: port 5(ra3) entering forwarding state Filesystem firmware binary used (/root/voip_fw/ar9_firmware.bin). Filesystem BBD binary used (/root/voip_fw/bbd_Usa.bin). BOARD_Easy50812_PrepareBoard : analogCh = 1, coderCh = 5 , DECT_Ch = 0 BOARD_Easy50812_PrepareBoard pBoard->nUsedChannels = 5 Set fxsFd 0 to /dev/vmmc11 Set channelFd 0 to /dev/vmmc11 Set channelFd 1 to /dev/vmmc12 Set channelFd 2 to /dev/vmmc13 Set channelFd 3 to /dev/vmmc14 Set channelFd 4 to /dev/vmmc15 VMMC [version 0x 0, type 0x 4, channels 1] ready! FW Version 4.2 VMMC Driver version 1.9.0.3 73M1966 TAPI Driver, Rev. 2.2, (c) 2007-2009 Teridian Semiconductor Corp. 73M1966 Driver, Rev. 2.7.3lq4, (c) 2007-2009 Teridian Semiconductor Corp. Set fxsFd 0 to /dev/vmmc11 Set channelFd 0 to /dev/vmmc11 Set channelFd 1 to /dev/vmmc12 Set channelFd 2 to /dev/vmmc13 Set channelFd 3 to /dev/vmmc14 Set channelFd 4 to /dev/vmmc15 PhoneEventRxTask() : error to open Dev_FD : -1 rm: cannot remove '/tmp/SIPPktDebug': No such file or directory voiceApp > APP_ADD_REQ towards IP Phone Toolkit Failed. *********************************************** icf_port_open_ipc_channel path = /var/iptk_es.chanl the open channel succeded exit from the es init br0: topology change detected, propagating br0: port 2(ra0) entering forwarding state stopping ftpd... done starting ftpd... done mini_httpd: exiting due to signal 15 socket: Address family not supported by protocol socket: Address family not supported by protocol socket: Address family not supported by protocol ip6_tables: (C) 2000-2006 Netfilter Core Team DSL[00]: ERROR - Function is only available in the SHOWTIME! DSL[00]: ERROR - Function is only available in the SHOWTIME! Sorry, rule does not exist. killall: upnpd: no process killed Jan 1 00:01:14 ccc_mr: cccRegModule(): register tr69FE ifx_ppa_init - init succeeded VCAUTOHUNT_LINKDETECTION Init! ZLD_SM_DownStream(LAN)=[1] ZLD_SM_UpStream(WAN)=[0] Session Match: Add WAN interface [nas1] Session Match: Add LAN interface [br0] Session Match: Add LAN interface [eth0.3901] killall: webipqd: no process killed killall: zyTimeZoneUpdater: no process killed mini_httpd: exiting due to signal 15 mini_httpd_ssl: exiting due to signal 15 socket: Address family not supported by protocol socket: Address family not supported by protocol socket: Address family not supported by protocol disable led DSL[00]: Reboot on training timeout (120)!!! DWC_otg: hc_xfer_timeout: dwc_core_num[0] --- timeout on channel 13 DWC_otg: start_hcchar_val 0x00988a00